Siglent

Soft Carry Case for SDS1000DL+/CML+, SDS1000X, SDS1000X-E, SDS2000X-E Series Weight 4 lbs Dimensions 18 × 9 × 4 in

Soft Carry Case for SDS2000X, SDS2000X Plus, SDS2000X HD, SDS5000X, SSA3000X，SVA1000X, SSA3000X-R, SSA3000X Plus Weight 4 lbs Dimensions 18 × 12 × 6 in

Bandwidth: 6 MHz (X1) / 200 MHz (X10) Switchable 85 pf / 16 pf Maximum input: 300 V / 600V Operating Temperature: -10 – 55 degrees C

Return Loss Bridge (1 MHz to 2.5 GHz), N-type(M) to N-type(M) adaptor (2 pcs) for measuring VSWR with the SSA3000X Plus series of spectrum analyzers. NOTE: On-screen VSWR calculations require the activation license for Reflection/VSWR for the specific analyzer you wish to use. This part number includes hardware only.

Bandwidth: 6 MHz (X1) / 70 MHz (X10) Switchable 85 pf / 18 pf Maximum input: 300 V / 600V Operating Temperature: -15 – 75 degrees C

Mechanical Calibration Kit for Vector Network Analyzers: Open(F), Short(F), Match(F,50), Through(F-F), 50 Ohms, DC – 4.5 GHz The F503ME and F503FE mechanical calibration standards for 50Ω N type coaxial systems encompass fixed terminations, open circuits, short circuits, and through adaptors, covering a frequency range from DC to 4.5 GHz. Their performance specifications closely resemble those of the Keysight 85032B/E mechanical calibration kit. Therefore, they serve as suitable alternatives to the 85032B/E kit or can be employed alongside the 85032B/E standard in network analyzers.

Mechanical Calibration Kit for Vector Network Analyzers: Open(F), Short(F), Match(F,50), Through(F-F), 50 Ohms, DC – 9 GHz The F504FS mechanical calibration standards for 50Ω N type coaxial systems comprise fixed terminations, open circuits, short circuits, and through adaptors, with specifications ranging from DC to 9 GHz. The performance specifications of the F504MS and F504FS closely resemble those of the Keysight 85032F mechanical calibration kit. Hence, they can serve as approximate substitutes for the 85032F kit or be utilized alongside the 85032F standard in network analyzers.

Mechanical Calibration Kit for Vector Network Analyzers: Includes 9 calibration elements: N-type Open (M,F), Short (M,F), Match/Load (M,F 50 Ohms), Through (M-M, M-F, F-F), DC – 9 GHz Torque wrench Carrying case The F504TS is a coaxial calibration assembly comprising both F504MS and F504FS sets. These economy 50Ω N type coaxial mechanical calibration standards consist of fixed terminations, open circuits, short circuits, and through adaptors, covering a frequency range from DC to 9 GHz. The performance specifications of F504MS and F504FS closely resemble those of the Keysight 85032F mechanical calibration kit. Therefore, they can function as approximate substitutes for the 85032F kit or be integrated with the 85032F standard in network analyzers.

Bandwidth: 6 MHz (X1) / 100 MHz (X10) Switchable 85 pf / 18 pf Maximum input: 300 V / 600V Operating Temperature: 0 – 50 degrees C

3.5 mm-Type Mechanical Calibration Kit for Vector Network Analyzers: Open (M), Short (M), Match (M,50), Through (M-M), 4.5 GHz The F603ME and F603FE mechanical calibration standards for economy 50Ω 3.5mm/SMA type coaxial systems encompass fixed terminations, open circuits, short circuits, and through adaptors, with specifications ranging from DC to 4.5 GHz. Their performance specifications closely resemble those of the Keysight 85033E mechanical calibration kit. Thus, they serve as suitable alternatives to the 85033E kit or can be integrated with the 85033E standard in network analyzers.

3.5 mm-Type Mechanical Calibration Kit for Vector Network Analyzers: Open (F), Short (F), Match (F,50), Through (F-F), 4.5 GHz The F603ME and F603FE mechanical calibration standards for economy 50Ω 3.5mm/SMA type coaxial systems encompass fixed terminations, open circuits, short circuits, and through adaptors, with specifications ranging from DC to 4.5 GHz. Their performance specifications closely resemble those of the Keysight 85033E mechanical calibration kit. Thus, they serve as suitable alternatives to the 85033E kit or can be integrated with the 85033E standard in network analyzers.

1 GHz active probe for use with the SIGLENT SDS5000X/SDS6000A series of oscilloscopes Single-ended (uses instrument ground. Not differential) Bandwidth (probe only) >1 GHz Bandwidth (with scope) 1 GHz (SDS5104X) 1 GHz (SDS6204A) Input capacitance 1.2 pF Input resistance 1 MΩ Offset range ±12 V Attenuation ratio (DC) ÷10 Offset accuracy < 3% DC gain accuracy < 3% Input dynamic range ±8 V Maximum input voltage (non-destructive) 20 V Cable length 130 cm

Accessory for use with the four-channel SDS 800X HD, SDS1000X HD, SDS1000X-E, SDS2000X-E, SDS3000X HD, SDS5000X, and SDS6000A oscilloscopes. Output Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in waveforms. The arbitrary waveforms can be accessed and edited by the EasyWave PC software. Requires the correct Function Generator Activation License for the specific oscilloscope (part number ends with -FG) Outputs: 1 Max. Output Frequency: 25 MHz Sampling Rate: 125 MSa/s Frequency Resolution: 1 μHz Frequency Accuracy: ±50 ppm Vertical Resolution: 14-bit Amplitude Range: 1.5 ～ +1.5 V (50Ω load), -3 ～ +3 V (High-Z load) Waveform Types: Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in waveforms Output impedance: 50 Ω±2% Protection: Over-Voltage Protection, Current-Limiting Protection Insulation Voltage: ±42 Vpk (for SAG2021I only)

Designed for use with all Siglent SDG function generators. Useful when a higher output power is required. Bandwidth: DC – 1 MHz Maximum frequency: 1 MHz Input impedance: 15 kOhms Input: +/- 6.5V Vpp (Gain: X1) — +/- 1.3Vpp (Gain: X10) Maximum output voltage: 25.4 Vpp Maximum output current: 1.12 A Maximum slew rate: >90 V/usec

Bandwidth: 50 MHz Rise Time ≤ 7 ns DC Accuracy ± 2% Max Input: 600 V CATIII, 1000 V CATII Max Differential Test Voltage (DC + Peak AC): 50 X: ±130 V, 500 X:±1300 V Input impedance/capacitance: 5 MΩ/<4 pF(Single-ended), 10 MΩ/< 2 pF(Two inputs) Power: DC 12 V/1.2 A Power supply

Used with the SDS-2000X-LA/SDS2000XP-16LA/SDS-5000X-16LA to add 16-channel digital input capability to the Siglent SDS2000X/SDS2000XP/5000X families of oscilloscopes. 500 MSa/sec * SDS-2000X-LA/SDS2000XP-16LA/SDS-5000X-16LA/SDS-60000Pro-16LA Firmware License Key required (Sold Separately) The kit includes: Qty 1 SPL2016 Wiring Harness Qty 20 SPL-C1 digital clips

Bandwidth: 350 MHz (X10) 12 pf Maximum input: 300V Operating Temperature: 0 – 50 degrees C Auto-Sense feature – Used with SDS2102X Plus, SDS2104X Plus, SDS2204X Plus, SDS2354X Plus, SDS5032X, and SDS5034X oscilloscopes

Bandwidth: 500 MHz 8-20 pf, 10 Mohm ± 1% Maximum input: CAT Ⅱ 400 Vrms Operating temperature 0 to 50 degrees

Bandwidth: 100 KHz Maximum Continuous Current: 20 Arms Peak Current: 60 A Switching Ratio: 50 mV/A, 2 mV/A DC Measurement Accuracy: +/- 2% (50 mV/A) (0.4 – 10 Apk) ; +/- 2% (5 mV/A) (1A – 60 Apk) Power: 9 V battery

Bandwidth: 150 KHz Maximum Continuous Current: 70 Arms Peak Current: 200 A Switching Ratio: 500 mV/A; 50 mV/A DC Measurement Accuracy: 500 mV/A (20 mA-14 ApK) ±3% ±20 mA; 50 mV/A (200 mA-100 ApK )±4%± 200 mA; 50 mV/A (100 A-140 ApK) ±15% Power: 9 V battery

The set includes three magnetic near-field probes and one electric near-field probe. Frequency range: 300 kHz ~ 3 GHz; resolution 25 mm; distinguished within 10 cm range of the magnetic field; for EMI radiation interference and the intensity detector

Rack mount kit for two instruments. Compatible with the SIGLENT SDG800, SDG1000, SDG1000X, SDG2000X, SDG5000 and SDG6000X series function generators and SDM3045X, SDM3055, SDM3065X digital multimeters. 3U height, Compatible with 19″ racks

Designed to hold a single Siglent function generator or digital multimeter. Function generators: SDG800, SDG1000, SDG1000X, SDG2000X and SDG5000 DMM: SDM3065X, SDM3055, SDM3055A and SDM3045X 3U Height, compatible with 19″ racks.

Compatible with Siglent SDS1202X-E, SDS1104X-E, SDS1204X-E, and SDS1000X-U Digital Oscilloscopes. 4U Height, compatible with 19″ racks. Also known as SDS1X-E-RMK