Accessories

The PLA2216 serves as a high-performance active logic probe for the MSO5000 series digital oscilloscope, thereby enabling the logic analyzer functionality. Active logic probe For use with Rigol MSO5000 Series Oscilloscope

Standard logic probe for MSO1000Z. Upgrades a DS1000Z Plus or DS1000Z-S Plus to an equivalent MSO. Includes front panel labels with MSO model number. Only works with the Plus models or as a replacement part for the MSO1000Z models. 16 inputs

Male N-to-BNC Cable 2 Ghz bandwidth Length 0.7 m (27.6 inches)

Instrument Carry Case for a DS1000 Series Oscilloscope

Accessory for use with the four-channel SDS 800X HD, SDS1000X HD, SDS1000X-E, SDS2000X-E, SDS3000X HD, SDS5000X, and SDS6000A oscilloscopes. Output Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in waveforms. The arbitrary waveforms can be accessed and edited by the EasyWave PC software. Requires the correct Function Generator Activation License for the specific oscilloscope (part number ends with -FG) Outputs: 1 Max. Output Frequency: 25 MHz Sampling Rate: 125 MSa/s Frequency Resolution: 1 μHz Frequency Accuracy: ±50 ppm Vertical Resolution: 14-bit Amplitude Range: 1.5 ～ +1.5 V (50Ω load), -3 ～ +3 V (High-Z load) Waveform Types: Sine, Square, Ramp, Pulse, Noise, DC and 45 built-in waveforms Output impedance: 50 Ω±2% Protection: Over-Voltage Protection, Current-Limiting Protection Insulation Voltage: ±42 Vpk (for SAG2021I only)

Instrument Carry Case for a DSA800 Spectrum Analyzer, DG4000 generator, or DS2000 scope.

The STB-3 was designed as a teaching / training aid used to demonstrate how to trigger and display complex signals on a modern oscilloscope. Signals include various sine and square waves, AM, burst, and common serial bus signals. Power is supplied by a standard USB cable.

Bandwidth: 6 MHz (X1) / 200 MHz (X10) Switchable 85 pf / 16 pf Maximum input: 300 V / 600V Operating Temperature: -10 – 55 degrees C

NFP-3 is used with RIGOL DSA series spectrum analyzer for the EMI tests of electronic products. It can be used to test the magnetic field strength and magnetic field coupling channels on the surface of the electronic components as well as the magnetic field environment near the electronic module so as to quickly locate the interference source. Frequency Range: 30MHz to 3GHz One set includes four types of probe, provides optimizing sensitivity and resolution Minimum resolution: 2mm; able to capture near field radiation of single circuit line

CT Mounting Bracket Kit Suitable for use with models 112, 113, 114, 115,117, 307 & GFM462

CT Mounting Bracket Kit Suitable for use with model 19

Rack-mounting kit for SDS6000 and SNA5000A series. 7U height. Compatible with 19″ racks.

Bandwidth: 50 MHz Maximum Continuous Current: 30 Arms Peak Current: 50 A Switching Ratio: 5 A / 30 A Accuracy: 5A(±1%±1mA);30A(±1%±10mA); Standard DC12V/1A power adapter

Mixed Signal hardware option for the four-channel SDS1000X-E、SDS2000X-E、SDS800X HD and SDS1000X HD oscilloscope series. NOTE: The oscilloscope will require MSO activation license software (Part number SDS1000X-E-16LA or SDS2000X-E-16LA). Also, Four-channel SDS1000X-E scopes require firmware version 6.1.20 or greater The kit includes: Qty 1 SBus Controller Qty 1 SBus cable Qty 1 SPL1016 Wiring Harness Qty 20 SPL-C1 digital clips

Compatible with Siglent SPD3303X, SPD3303X-E, SPD3303C Series DC Power Supplies. Holds one power supply instrument. 4U Height, compatible with 19″ racks.

Compatible with Siglent SDS1202X-E, SDS1104X-E, SDS1204X-E, and SDS1000X-U Digital Oscilloscopes. 4U Height, compatible with 19″ racks. Also known as SDS1X-E-RMK

Designed to hold a single Siglent function generator or digital multimeter. Function generators: SDG800, SDG1000, SDG1000X, SDG2000X and SDG5000 DMM: SDM3065X, SDM3055, SDM3055A and SDM3045X 3U Height, compatible with 19″ racks.

Rack mount kit for two instruments. Compatible with the SIGLENT SDG800, SDG1000, SDG1000X, SDG2000X, SDG5000 and SDG6000X series function generators and SDM3045X, SDM3055, SDM3065X digital multimeters. 3U height, Compatible with 19″ racks

The set includes three magnetic near-field probes and one electric near-field probe. Frequency range: 300 kHz ~ 3 GHz; resolution 25 mm; distinguished within 10 cm range of the magnetic field; for EMI radiation interference and the intensity detector

Bandwidth: 150 KHz Maximum Continuous Current: 70 Arms Peak Current: 200 A Switching Ratio: 500 mV/A; 50 mV/A DC Measurement Accuracy: 500 mV/A (20 mA-14 ApK) ±3% ±20 mA; 50 mV/A (200 mA-100 ApK )±4%± 200 mA; 50 mV/A (100 A-140 ApK) ±15% Power: 9 V battery

Bandwidth: 100 KHz Maximum Continuous Current: 20 Arms Peak Current: 60 A Switching Ratio: 50 mV/A, 2 mV/A DC Measurement Accuracy: +/- 2% (50 mV/A) (0.4 – 10 Apk) ; +/- 2% (5 mV/A) (1A – 60 Apk) Power: 9 V battery

Bandwidth: 500 MHz 8-20 pf, 10 Mohm ± 1% Maximum input: CAT Ⅱ 400 Vrms Operating temperature 0 to 50 degrees

Bandwidth: 350 MHz (X10) 12 pf Maximum input: 300V Operating Temperature: 0 – 50 degrees C Auto-Sense feature – Used with SDS2102X Plus, SDS2104X Plus, SDS2204X Plus, SDS2354X Plus, SDS5032X, and SDS5034X oscilloscopes

Used with the SDS-2000X-LA/SDS2000XP-16LA/SDS-5000X-16LA to add 16-channel digital input capability to the Siglent SDS2000X/SDS2000XP/5000X families of oscilloscopes. 500 MSa/sec * SDS-2000X-LA/SDS2000XP-16LA/SDS-5000X-16LA/SDS-60000Pro-16LA Firmware License Key required (Sold Separately) The kit includes: Qty 1 SPL2016 Wiring Harness Qty 20 SPL-C1 digital clips