Accessories

Logic probe kit for MSO8000 Series. Includes cable, leads and grabber clips.

Vector Network Analysis Calibration kit for RSA N models. This kit enables RSA calibration from DC to 1.5 GHz

RF Cable and adaptor kit

Front Panel Cover for MSO5000

Rack Mounting Kit for ONE DG1000Z Series Generator

150 MHz Passive Probe with 1x:10x selector. With bandwidth of 20 MHz in 1x mode 150 MHz Passive Probe Bandwidth of 20 MHz in 1x Mode Compensation Range: 10 pF to 25 pF Cable Length: 120 ± 2 cm Probe Tip Diameter: 4.8 mm

Demonstration signal board for RIGOL Oscilloscopes

The RP1002C current probe enables a general purpose oscilloscope to display AC and DC current signals up to 100 A Peak (70 A RMS). The RP1002C current probe can also make AC and DC measurements with a multimeter by using the BNC-to-banana plug adapter. DC and AC Frequency range: DC to 1MHz up to 140A peak (non-continuous) Ranges of 0.05V/A,0.5V/A for greater sensitivity Battery powered 9V internal for maximum external noise supression External psu socket provided (supplied with recommended 230V AC mains adapter for EU fitting - voltage rated for UK Mains voltage ranges

TEST LEAD SET FOR DMM

350 MHz Passive Probe with 1x:10x selector. With bandwidth of 35 MHz in 1x mode 350 MHz Passive Probe Bandwidth of 35 MHz in 1x Mode Compensation Range: 10 pF to 25 pF Cable Length: 120 ± 2 cm Probe Tip Diameter: 4.6 mm

150 MHz Passive Probe with 1x:10x selector. With bandwidth of 35 MHz in 1x mode 150 MHz Passive Probe Bandwidth of 35 MHz in 1x Mode Compensation Range: 10 pF to 25 pF Cable Length: 120 ± 2 cm Probe Tip Diameter: 4.6 mm

The RP1000D series high voltage differential probe can convert high differential input voltage 7000Vpp to low voltage and display the waveform on oscilloscope. Its working frequency is up to 100MHz (RP1100D) and it is rather suitable for large electricity test and R&D. DC-100 MHz 7000 Vpp

The coaxial fixed attenuator is applicable to the situations that require power level reduction and circuit matching. It can absorb the energy of the transmission wires quantitatively, extend the power range, control the power level and make precise measurements of the power and amplitude of various signal generators by working with small power meter, multimeter or oscilloscope. Frequency Range: DC to 1 GHz Attenuation Value: 40 dB Impedance: 50 O Power: 1 W

Passive High Voltage Probe for use with Rigol Oscilloscopes Bandwidth: DC-300 MHz Attenuation Ratio: 100:1 Max. Input voltage CAT|2000V(DC+AC) CAT||1500V(DC+AC)

The RP1001C current probe enables a general purpose oscilloscope to display AC and DC current signals up to 100 A Peak (70 A RMS). The RP1001C current probe can also make AC and DC measurements with a multimeter by using the BNC-to-banana plug adapter. DC and AC Frequency range: DC to 300KHz Ranges of 0.01V/A,0.1V/A Battery powered 9V internal for maximum external noise supression

RP1000D series high voltage differential probe can convert high differential input voltage to low voltage and display the waveform on the oscilloscope. Its working frequency is up to 25MHz(RP1025D), 50MHz(RP1050D) and 100MHz(RP1100D) and it is rather suitable forlarge electricity test and R&D. RP1000D series high voltage differential probe is applicable to general purpose oscilloscope and the labeled attenuation ratios are those when the input impedance of the oscilloscope is 1MO. Theattenuation ratios will double when the input impedance of the oscilloscope is 50O. Frequency Range: DC to 50 MHz Input Voltage Range: 7000 Vpp

VSWR Bridge with VSWR-DSA800, VSWR-DSA1000 licenses included Frequency range: 1 MHz - 3.2 GHz, Typical Directivity: = 30 dB

BNC Cable (length 1 meter)

RP1000D series high voltage differential probe can convert high differential input voltage to low voltage and display the waveform on the oscilloscope. Its working frequency is up to 25MHz(RP1025D), 50MHz(RP1050D) and 100MHz(RP1100D) and it is rather suitable for large electricity test and R&D. RP1000D series high voltage differential probe is applicable to general purpose oscilloscope and the labeled attenuation ratios are those when the input impedance of the oscilloscope is 1MO. The attenuation ratios will double when the input impedance of the oscilloscope is 50O. Frequency Range: DC to 25 MHz Input Voltage Range: 1400 Vpp

CT Mounting Bracket Kit Suitable for use with models 8SHT, 19SHT, GFL325T & GFL425T

Shorting Style Terminal Block 6 Poles c/w Cover Application Control and power wire termination. Short circuiting versions for meter servicing, CT tap changing, ...etc.

Shorting Style Terminal Block 8 Poles c/w Cover Application Control and power wire termination. Short circuiting versions for meter servicing, CT tap changing, ...etc.

Shorting Style Terminal Block 4 Poles c/w Cover Application Control and power wire termination. Short circuiting versions for meter servicing, CT tap changing, ...etc.

Shorting Style Terminal Block 4 Poles Application Control and power wire termination. Short circuiting versions for meter servicing, CT tap changing, ...etc.